- Joined
- May 7, 2023
- Messages
- 148
- Reaction score
- 14
- Points
- 18
Can you make molar calculation of p2np nabh4 amphetamine synthesis with 3gr
IPA 40-50 ml
H2O 12,5 ml
NaBH4 3,5 g
P2NP 2 g
CuCl2 +-0,2 g
NaOH (25% water solution) 16 ml
Acetone (dry) 5-10 ml
In this case, how many ml of ipa and h2o should I use and how many ml of water should I make a solution of copper chloride 200mg
I am not exercising the dilligence of doing the math also, but double check. The reactant proportions in your recipe for which you are following, converted into moles. Figure out the ratio and apply that to your solvents. If it was originally for 2g of CuCl2 then, of course, 200mg is %10 of that. So then find %10 of the portion of solvent you are instructed to use. That one ratio needs to be applied to all portions of all ingredients to have the same exact amounts. Technically, moles need not be calculated, but it is good practice, and verifies your work up.
((((( IPA 40-50 ml
H2O 12,5 ml
NaBH4 3,5 g
P2NP 2 g
CuCl2 +-0,2 g
NaOH (25% water solution) 16 ml
Acetone (dry) 5-10 ml
In this case, how many ml of ipa and h2o should I use and how many ml of water should I make a solution of copper chloride 200mg ))))) <-- Where did you get these portions? This looks like a customized micro batch?
CuCl2 is already 0.2g in the portion list so it says to use, whatever, 40-50ml IPA and 12.5ml H2O. I am confused, Are these not already calculated?
That is what I am trying to figure out, I will help you make sure it is correct if you need. If you are just using it for a 'liquid/liquid' extraction then it is probably unnecessary work - just eyeball it, you can't really screw it up with amount, just don't over do it.
What calculations? What recipe instructions are you using for portions?
Will the copper chloride in my synthesis be 200 mg?
I was asking you that, my friend. Where did you get these portions for the recipe? Are they yours? Or how were they figured? This is only going to make like a half gram of amph or something or other insignificant ...
I was asking you that, my friend. Where did you get these portions for the recipe? Are they yours? Or how were they figured? This is only going to make like a half gram of amph or something or other insignificant ...
my calculation on the p2np nabh4 amphetamine method
IPA 40-50 ml
H2O 12,5 ml
NaBH4 3.5 g
P2NP 2 g
CuCl2 +-0.2 g 9.675 H2o
NaOH (25% water solution) 16 ml
Acetone (dry) 5-10 ml
I first put ipa and h2o and mix for 2 minutes, then I add p2np, then I dissolve 0.200mg copper chloride in 5ml water and add it, but the temperature does not increase.
Tuco my friend,
I looked at the one pot synth recipe and the CuCl2/H2O solution is in 1/2 ratio meaning for 200mg CuCl2 you would use 400mg H2O as your solution proportion.
The temperature does not increase perhaps because it is such a small scale. Also you are using a two liter flask - kind of big for what you are working with, no?
After the CuCl2 solution is added, the temperature is maintained at 80c for 30 minutes with help of external heating. You got a hot plate you can dial in?
Add your NaOH solution to base. Seperate aqueous phase using IPA and reduce back into freebase with a vacuum.
Dissolve freebase into acetone and add H2SO4 until pH 6.
Place in freezer for ~12 hours
Collect salt and wash with cold dry acetone until it is white colored.
If you are still having trouble with these portions I would suggest using a larger batch. That is a 45 page thread, and it is not the only one. There has to be more info in there you can use. Read, brother.
Our team brings together the best specialists from different fields.
We are ready to share our experience, discuss difficult issues and find new solutions.
Connect notifications to always stay in touch with the forum!